manualshive.com logo in svg

Daikin MC70L3VM L-Series, Руководство по обслуживанию

Поделиться
Скачать
Daikin MC70L3VM L-Series Скачать руководство пользователя страница 31

Childproof Lock Function: Special Mode

SiBE811120

30

Photocatalytic Air Purifier L-Series

5. Childproof Lock Function: Special Mode

Outline

In normal mode, once you disconnect the power plug, the childproof lock function is cancelled.
The special mode enables the childproof lock function to resume even after the power plug is 
disconnected. 
It is useful when you keep the remote controller away from the small children or the guests in 
hotel rooms to prevent them from mishandling.

Detail

Note:

★

1

★

2

The air purifier is operating with the childproof lock function on.

Disconnect the power plug to stop operation.

Insert the power plug.

Start operation.

Normal operation

Operation starts in special mode
The childproof lock function resumes.

Special mode

The childproof lock function is cancelled.
To set the function effective, press the 
childproof lock button on the remote 
controller for 2 seconds again. 



2

Pressing the [ON / OFF / Mode change] button 
on the main unit, insert the power plug. 



1

(R13827)

(R14650)

ON / OFF / Mode change button

(R14651)

Childproof lock

• You can release the childproof lock by pressing             again for 

about 2 seconds. 
You can also release the childproof lock when you disconnect 
the power plug once, and after 3 seconds or more, reconnect the 
power plug.

• Press             for about 2 seconds to engage the childproof lock.

Содержание MC70L3VM L-Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды