Daikin MC70L3VM L-Series Скачать руководство пользователя

Страница: 16 / 59

SiBE811120

Operation Manual

Photocatalytic Air Purifier L-Series

Operation lamp

Filter reset button

Page 14.

OFF TIMER lamp (yellow)

Page 21.

Filter lamp (orange)

UNIT lamp (orange)

Page 21.

Page 19, 20.

Odour sensor lamp

Lights up

Odour

Strong

Green

• Turbo lamp (orange)
• Anti-pollen lamp (green)
• Sleep mode lamp (green)

The operation mode changes each time
the button is pressed.

ON / OFF / Mode

change button

The filter lamp is turned off by pressing
the button for 5 seconds after the pleated
filter is replaced with a new one.

The filter lamp lights up when the pleated filter
needs replacement and starts blinking when a
certain time has elapsed after the lamp turned on.

The three-colour indicators (green, yellow, red) indicate the odour level.

• When the air is clean, the green lamp lights up.

In the following case, only the green lamp lights up for the initial
1 minute. The initial level of odour is recorded as the standard
level.

1) Operation directly after attaching the front panel and UNIT1
2) Operation directly after reconnecting the power plug

If the odour level remains constant without intensifying or weakening,
the odour sensor may not detect even strong odours.

The odour sensor may not detect certain types of odours such as pet
odours other than ammonia, garlic, etc.

Even if only the green lamp lights up, you may notice some smell
because the sensitivity is different among individuals.
If bothered by odours, set airflow manual operation and run the unit at a
higher airflow rate.

• “UNIT2”

This lamp lights up when it is time to clean the streamer unit.

• Even when the lamp does not light up, clean the streamer unit once

every 3 months.

Detectable

Sometimes detectable

Cigarette odours, cooking odours, pet and toilet odours, raw waste odours, mildew odours, sprays,
alcohol

Sudden changes in temperature and humidity, odourless gases such as carbon monoxide, steam, oil
vapours, gas from combustion appliances

Weak

Yellow

Red

• “UNIT1”

This lamp lights up when it is time to clean the plasma

ioniser.

Содержание MC70L3VM L-Series




























































Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Похожие инструкции для MC70L3VM L-Series

Бренды по названию

Популярные бренды

Daikin MC70L3VM L-Series, Руководство по обслуживанию

Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Похожие инструкции для MC70L3VM L-Series

Бренды по названию

Популярные бренды