Daikin MC70L3VM L-Series Скачать руководство пользователя

Страница: 17 / 59

Operation Manual

SiBE811120

Photocatalytic Air Purifier L-Series

4.4

Preparation before Operation

A
B

Preparation before Operation

Accessories check

Confirm all the accessories are included.

Pleated filter…1 sheet
< For initial installation >

Inside cushion

Operation manual…1 book
(This booklet)

Inside package

Remote controller…1 unit

In remote controller
storage slot

Pleated filters…4 sheets
< Replacement filters >

In filter container

How to attach the pleated
filter

Make sure to attach the pleated filter before starting
operation.

Remove the front panel.

• Push the 2 clips (right and left), and pull the front panel

upward and remove it.

Front panel

Clip
(1 each on right and left)

Push

Remove UNIT1.

• Holding UNIT1 by the handles, pull UNIT1 upward and

remove it.

1)
Pull

Handles

UNIT1

2)
Up

Remove the deodorising catalyst unit.

• Holding the deodorising catalyst unit by the handles, pull

the deodorising catalyst unit upward and remove it.

Handles

1)
Pull

Deodorising catalyst unit

2)
Up

Содержание MC70L3VM L-Series




























































Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Похожие инструкции для MC70L3VM L-Series

Бренды по названию

Популярные бренды

Daikin MC70L3VM L-Series, Руководство по обслуживанию

Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Похожие инструкции для MC70L3VM L-Series

Бренды по названию

Популярные бренды