Unitary products group HA090 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 20

Unitary products group HA090 Скачать руководство пользователя страница 1

CONTENTS

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . 4

AGENCY APPROVALS . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

See the following page for a complete Table of Contents.

NOTES, CAUTIONS AND WARNINGS

The installer should pay particular attention to the words:
NOTE, CAUTION, and WARNING. Notes are intended to
clarify or make the installation easier. Cautions are given
to prevent equipment damage. Warnings are given to
alert installer that personal injury and/or equipment dam-
age may result if installation procedure is not handled
properly.

INSTALLATION
MANUAL

CAUTION:

READ ALL SAFETY GUIDES BEFORE YOU
BEGIN TO INSTALL YOUR UNIT.

SAVE THIS MANUAL

208/230/460
VOLT ONLY

208/230/460
VOLT ONLY

SPLIT-SYSTEM

CONDENSING UNITS

(AIR COOLED)

MODEL: HA090

035-18204-001-B-0703

1
2
3
...
»

Содержание HA090





















Отзывы:

Нет отзывов