Daikin MC70L3VM L-Series Скачать руководство пользователя страница 47

Страница: 47 / 59

Removal Procedure

SiBE811120

Photocatalytic Air Purifier L-Series

9.3

Removal of Ionized Wire

Procedure

Warning

Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.

Step

Procedure

Points

Unfasten the 2 hooks
and lift the opposing
pole plate to detach.

The opposing pole plate has
the same shape in 4
directions.

Pinch and detach the
ionized wires with
pincers.

Caution

Be careful not to get your hands
cut by the ionized wires.

Once removed, the ionized
wires cannot be reused.

When cleaning the ionized
wires, do not remove them.
(Refer to the Operation
Manual.)

Remove the 3 screws
and remove the ionized
wire mounting frame
and contact switch.

Remove the 3 screws
and remove the contact
switch for ionized wire.

Hook

(R12351)

(R12352)

Opposing
pole plate

Ionized wire

(R12353)

(R12354)

Contact switch

Ionized wire
mounting frame

Contact switch
for ionized wire

Содержание MC70L3VM L-Series




























































Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Бренды по названию

Популярные бренды

Daikin MC70L3VM L-Series, Руководство по обслуживанию

Результаты поиска

Содержание MC70L3VM L-Series

Отзывы:

Бренды по названию

Популярные бренды