manualshive.com logo in svg

Daikin MC70L3VM L-Series, Руководство по обслуживанию

Поделиться
Скачать
Daikin MC70L3VM L-Series Скачать руководство пользователя страница 23

Operation Manual

SiBE811120

22

Photocatalytic Air Purifier L-Series

4.6

Quick Reference Table of Maintenance

15

Quick Reference Table of Maintenance

WARNING

1

Front panel

2

Prefilter

3

4

Wipe

Vacuum cleaner

Rinse with water

Soak, drain and dry

Wipe

Soak, drain and dry

Wipe

Care and Cleaning 

Page 19, 20.

Ionised wire

Ionising frame

Opposing pole plates

NOTE

WARNING

UNIT1

(Plasma ioniser)

UNIT2

(Streamer unit)

The figure above shows 

UNIT1 after the opposing 
pole plates are removed.

Once every 3 months or if 

the “UNIT2” lamp lights

If the “UNIT1” 

lamp lights

• Wipe off the dirt with a cloth 

slightly moistened with water.

• In the case of heavy dirt, wipe it 

off with a cloth moistened with 
neutral detergent.

• Do not use hard brushes, etc.

• Use a vacuum cleaner to 

remove the dust from the 
prefilter, and wash it with water.

• In the case of heavy dirt, wash 

the prefilter with a soft brush or 
neutral detergent and dry it well 
in the shade.

Dry the prefilter completely before 
using it because the “UNIT1” lamp 

may light up if any water drops 
remain on the prefilter.

• When detergent is used, wipe the detergent off the surface to 

prevent any residue.

• Do not dry the prefilter in a place exposed to direct sunlight.
• Do not use hot water with a temperature of 50˚C or higher for 

cleaning the parts.

• Do not dry the parts over a fire.

It may cause discolouration or deformation of the parts and the 
parts may become unusable.

• Do not use gasoline, benzene, thinner, scouring powder, 

kerosene, alcohol, etc.
(Cracking, electric shock or fire may occur.)

• Do not wash the main unit with water.

(Electric shock, fire or malfunction may occur.)

Before performing maintenance, stop the unit and disconnect the power plug. (It may cause electric shock or injury.)

Remove the parts for maintenance in numerical order.
For details on removing and attaching each part, see  

X

Page 17.  

 .

If it gets dirty

Once every 2 weeks

• Use a vacuum cleaner to remove the dust.
• Soak in lukewarm water or water. (About 1 hour)
• Dry throughly after soaking.

Содержание MC70L3VM L-Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды