Cypress PSoC CY8CTMG20 Series, Техническое справочное руководство

Страница: 129 / 308

PSoC CY8CTMG20x and CY8CTST200 TRM, Document No. 001-53603 Rev. *C 129
I2C Slave
Bit 3: Address.
This bit is set when an address is received. This consists of
a Start or Restart, and an address byte.
In slave mode when this status is set, firmware reads the
received address from the data register and compares it
with its own address. If the address does not match, the
firmware writes a NACK indication to this register. No further
interrupts occur until the next address is received. If the
address does match, firmware must ACK the received byte,
then byte complete interrupts are generated on subsequent
bytes of the transfer.
When in I
2
C compatibility mode the Address bit should not
be cleared between a start and the next byte complete. If it
is cleared during this time the start status is cleared inter-
nally.
Bit 2: Transmit. This bit sets the direction of the shifter for
a subsequent byte transfer. The shifter is always shifting in
data from the I
2
C bus, but a write of ‘1’ enables the output of
the shifter to drive the SDA output line. Since a write to this
register initiates the next transfer, data must be written to the
data register before writing this bit. In receive mode, the pre-
viously received data must have been read from the data
register before this write. Firmware derives this direction
from the RW bit in the received slave address.
This direction control is only valid for data transfers. The
direction of address bytes is determined by the hardware.
Bit 1: LRB. Last Received Bit. This is the last received bit
in response to a previously transmitted byte. In transmit
mode, the hardware sends a byte from the data register and
clock in an acknowledge bit from the receiver. Upon the sub-
sequent byte complete interrupt, firmware checks the value
of this bit. A ‘0’ is the ACK value and a ‘1’ is a NACK value.
The meaning of LRB depends upon the current operating
mode.
‘0‘: ACK. The master wants to read another byte. The
slave loads the next byte into the I2C_DR Register and sets
the Transmit bit in the I2C_SCR register to continue the
transfer.
‘1’: NACK. The master is done reading bytes. The slave
reverts to IDLE state on the subsequent I2C_SCR write
(regardless of the value written).
Bit 0: Byte Complete. The I
2
C hardware operates on a
byte basis. In transmit mode, this bit is set and an interrupt is
generated at the end of nine bits (the transmitted byte + the
received ACK). In receive mode, the bit is set after the eight
bits of data are received. When this bit is set, an interrupt is
generated at these data sampling points, which are associ-
ated with the SCL input clock rising (see details in
Timing
Diagrams on page 130 ). If the PSoC device responds with a
write back to this register before the subsequent falling edge
of SCL (which is approximately one-half bit time), the trans-
fer continues without interruption. However, if the device
cannot respond within that time, the hardware holds the
SCL line low, stalling the I
2
C bus. A subsequent write to the
I2C_SCR register releases the stall.
For additional information, refer to the I2C_SCR register on
page 240 .
15.3.11 I2C_DR Register
The I
2
C Data Register (I2C_DR) provides read/write access
to the Shift register.
Bits 7 to 0: Data[7:0]. This register is not buffered; there-
fore, writes and valid data reads occur at specific points in
the transfer. These cases are outlined as follows:
■
Slave Receiver – Data in the I2C_DR register is only
valid for reading when the Byte Complete status bit is
set. Data bytes must be read from the I2C_DR register
before writing to the I2C_SCR Register , which continues
the transfer.
■
Slave Transmitter – Data bytes must be written to the
I2C_DR register before the Transmit bit is set in the
I2C_SCR Register , which continues the transfer.
For additional information, refer to the I2C_DR register on
page 241 .
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Access
0,D8h I2C_DR Data[7:0] RW : 00
[+] Feedback