manualshive.com logo in svg

Cypress PSoC CY8CTMG20 Series, Техническое справочное руководство

Cypress PSoC CY8CTMG20 Series - технический справочник, доступный для бесплатного скачивания с manualshive.com. Руководство содержит полезные инструкции и информацию о продукте. Загляните на manualshive.com, чтобы скачать свой экземпляр руководства пользователя.

Поделиться
Скачать
background image

PSoC CY8CTMG20x and CY8CTST200 TRM, Document No. 001-53603 Rev. *C

169

Full-Speed USB

(Self-powered devices do not need to go into Suspend
mode.) This condition is detected by monitoring the Bus
Activity bit in the USB_CR1 register. This bit must be polled
periodically. If it reads high (bus activity present), it must be
cleared by firmware. If no activity is detected for the desired
time (for example, 3 ms), then the device must enter Sus-
pend mode. 

Not all sleep modes preserve the USB configuration register
states during sleep. The Standby I2C-USB mode is the pre-
ferred sleep mode for USB operation because the state of
all USB registers is maintained during sleep. The other
sleep modes do not preserve all of these registers to save
sleep power. 

The USB regulator settings must not be changed when
entering sleep state, since the regulator automatically enters
a low power state for the given regulator mode (pass-
through or regulating). 

20.2.5.1

Using Standby I2C-USB Sleep Mode 
for USB Suspend

To enter Standby I2C-USB mode, firmware powers down
the desired functions, as it would to enter a Standby I2C-
USB mode sleep state as documented in 

10.1.1 Sleep Con-

trol Implementation Logic on page 74

, including writing the

SLEEP bit of the CPU_SCR0 register. In this mode, USB
configuration registers and data are preserved during sleep. 

20.2.5.2

Using Standby or Deep Sleep Modes 
for USB Suspend

The Standby and Deep Sleep modes do not have hardware
supported for USB suspend operation because not all USB
registers are preserved in these modes. In USB parts, if
there is a need to enter Standby or Deep Sleep mode, then
user firmware must save the non-retained registers to
SRAM before entering into sleep and restore these registers
once the device wakes up. The list of these registers is
given below. Some configuration registers retain their val-
ues in all sleep modes: USB_CR0, USB_CR1, USBIO_CR0,
USBIO_CR1, IMO_TR, IMO_TR1. In addition, the USB
SRAM contents are preserved in all sleep modes. 

The USB registers that retain state in Standby I2C-USB
mode but not in other sleep modes are: the endpoint control
registers (EPx_CRx), endpoint PMA write address
(PMAx_WA)/read address (PMAx_RA) registers, PMA data
registers (PMAx_DR), endpoint count registers
(EPx_CNTx), endpoint 0 data register (EP0_DRx) and start
of frame registers (USB_SOFx). These registers are reset
after the device comes out of sleep. 

(An alternative is to simply disconnect from the USB bus
before going into one of these sleep modes, and then re-
connect to re-initialize the USB system after waking up.)

20.2.5.3

Wakeup from Suspend

The USB wake interrupt must be enabled to allow the device
to exit the sleep state when there is activity on the USB bus.
This interrupt can be enabled at any time since it only
asserts when the device is in the sleep state. Other inter-
rupts may be optionally enabled, such as the sleep interrupt,
GPIO, I2C, to periodically wake the device while in USB
suspend state. The USB wake interrupt can wake up the
device from all the three sleep states (Standby sleep, I2C-
USB sleep and Deep Sleep). If D+ is low when the SLEEP
bit is being set, the device briefly enters sleep state, and
then exits sleep due to the USB wake interrupt. 

By carefully using a sleep timer interrupt, the device can
wake periodically, monitor the environment, and return to
sleep while maintaining a low average current that meets
the USB suspend current specification. 

If the device needs to issue a resume signal to the USB sys-
tem, firmware can write to the TEN and TD bits in the
USBIO_CR0 register to manually force a K state on the bus.
Using these bits produces signaling that meets the USB tim-
ing specifications. 

When driving a resume, the J state (TD=1) must be driven
briefly before driving the K state (TD=0). The steps are sum-
marized as follows:
1. Drive the J state (TEN=1, TD=1) for one instruction.
2. Drive the resume, or K state (TEN=1, TD=0) for the 

proper time (1 ms to 15 ms).

3. Stop driving the USB bus manually (TEN=0).

20.2.6

Regulator

The transceiver contains a built-in regulator that can be
used to power the transceiver from the USB bus voltage or
other supply around 5V. The regulator supplies the proper
levels for USB signals, which switch between 0V and 3.3V
nominally. If the PSoC device is operating with a Vdd supply
near 3.3V, then the regulator must be placed into a pass-
through mode so that the Vdd voltage is directly supplied to
the transceiver, without regulation. The RegEnable bit (bit 0
in the USB_CR1 register) is used to pick between the regu-
lating mode (5V supply) or the passthrough mode (3.3V sup-
ply). At power up, the regulator is automatically held in pass-
through mode, but the USB transceiver pins are tristated.

[+] Feedback

Содержание PSoC CY8CTMG20 Series





















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PSoC CY8CTMG20 Series

ABB ControlMaster CM15 Commissioning Instructions preview
ControlMaster CM15
Бренд: ABB Страницы: 28
Xylem Bell & Gossett Technologic PPS Quick Start Manual preview
Bell & Gossett Technologic PPS
Бренд: Xylem Страницы: 20
Anritsu NF7600 Series Operation Manual preview
NF7600 Series
Бренд: Anritsu Страницы: 74
Adaptec ASR-2045 Important Information About Issues And Errata preview
ASR-2045
Бренд: Adaptec Страницы: 4
CP Electronics AR-SG-4SM-W Product Manual preview
AR-SG-4SM-W
Бренд: CP Electronics Страницы: 12
Oomlout ARDX Experimenter'S Manual preview
ARDX
Бренд: Oomlout Страницы: 32
Haiwell S04AI User Manual & Application Case preview
S04AI
Бренд: Haiwell Страницы: 18
Toho Electronics TTM-339 Operation Manual preview
TTM-339
Бренд: Toho Electronics Страницы: 32
Inca PSJ2 User Manual preview
PSJ2
Бренд: Inca Страницы: 11
Magnetek SBN Series Instruction Manual preview
SBN Series
Бренд: Magnetek Страницы: 19
Aruba Networks 7030-MNT-19 Installation Manual preview
7030-MNT-19
Бренд: Aruba Networks Страницы: 2
Samson TROVIS 5724-3 Mounting And Operating Instructions preview
TROVIS 5724-3
Бренд: Samson Страницы: 72
Aqua Lung Legend LX Second Stage Technical Maintenance Manual preview
Legend LX Second Stage
Бренд: Aqua Lung Страницы: 18
mikroElektronika mikromedia for dsPIC3 User Manual preview
mikromedia for dsPIC3
Бренд: mikroElektronika Страницы: 36
Altronix Maximal11V Installation Manual preview
Maximal11V
Бренд: Altronix Страницы: 20
Baldor BC142 Installation And Operation Manual preview
BC142
Бренд: Baldor Страницы: 33
Digisol RANGER SERIES Quick Installation Manual preview
RANGER SERIES
Бренд: Digisol Страницы: 28
Balcrank 3330-091 Operation, Installation, Maintenance And Repair Manual preview
3330-091
Бренд: Balcrank Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды