COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 96

Страница: 96 / 176

Service

98-175666-C

Chapter 4: Setup of the antenna

4-36

calibration has completed. In case of failure, see the table in the following section

for a description of error codes during calibration.

The following table shows the error codes that might be displayed during a

calibration.

Cable calibration

You must make a cable calibration. It is also recommended to make a cable calibration

when servicing the system to check if the antenna cable is still in good order. If the

attenuator margin changes by 2 dB or more after a cable calibration, it is

recommended to do a P1dB compression measurement to verify that the VSAT

modem configuration is correct.
1. Select

Service > Calibration

2. In the section

TX cable calibration

, select the

Type

• Cable calibration: The system will make a complete cable calibration

(recommended).

• Disable TX cable calibration: The gain is set at a maximum and no cable

calibration is made. It is up to the modem to make the necessary adjustments.

3. Click

Start

4. Wait typically for 2 minutes for the calibration to finish. A message is displayed

when the calibration has been completed successfully.The screen shows how

Important

It is strongly recommended to verify the result of a calibration

performed with user defined data. This can be done by making a new

calibration on a different satellite and verify that the resulting

Azimuth calibration value differs less than one degree.

Error

code

Explanation

The elevation of the selected satellite is too low. Select another

satellite.

The elevation of the selected satellite is too high. Select another

satellite.

The calibration values could not be saved. Possibly due to defective

hardware.

The antenna could not point with sufficient precision. Check that

the antenna is mounted in a stable way. Other possible causes

might be electrical or mechanical faults.

No signal received. Check that there is free line of sight. Try again or

try with another satellite.

RF setup error, e.g. missing or invalid TX frequency.

Invalid satellite, e.g. satellite not visible.

Unknown error

Table 4-21: Possible error codes during calibration

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды