COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 115

Страница: 115 / 176

98-175666-C

Appendix A: Technical specifications

A-3

Specifications SAILOR 600 XTR GX-R2

A.2 Specifications SAILOR 600 XTR GX-R2

www.cobhamsatcom.com

BELOW DECK UNIT (BDU)

Dimensions

1U 19” rack mount

HxWxD: 4.4 x 48 x 33 cm / 1.73” x 18.9” x 13”

Weight

3.6 kg / 8 lb

Temperature (ambient)

Operational: -25°C to +55°C / -13°F to +131°F

Storage: -40°C to +85°C / -40°F to +185°F

Humidity

EN 60945 Protected, 95% (non-condensing)

IP class

IP30

Compass safe distance

0.3 m / 12” to EN60945

,QWHUIDFHV

[0DOH1&RQQHFWRUIRUDQWHQQD5)&DEOH

with automatic cable loss compensation.

[)&RQQHFWRUVƻIRU5[DQG7[WR96$7PRGHP

1 x Ethernet Data (VSAT Modem Control)

2 x Ethernet (User)

1 x Ethernet (Remote access)

[(WKHUQHWIRU6HUYLFHDQG&RQ¿JXUDWLRQ

1 x RJ-45, RS-422 Data (VSAT Modem Control)

1 x RJ-45, RS-232 Data (VSAT Modem Control)

1 x RJ-45, NMEA 0183 (RS-422 / RS-232) for Gyro/

GPS Compass and external GPS input

1 x RJ-45, 4 x General purpose GPIO, Tx mute and Rx lock.

1 x AC Power Input

1 x Grounding bolt

User Interface

Webserver, OLED display (red), 5 pushbuttons, 3

GLVFUHWHLQGLFDWRU/('VDQG2Q2໤VZLWFK7;0XWH

and Modem Lock indicator.

Temperature control

Built-in fan

No transmit zones

Programmable, 8 zones with azimuth and elevation

Real-time blocking map recorder

Remote management and IoT

HTTPS, SSH, Telnet, SNMP Traps, Syslog, CLI,

Diagnostic, Statistic, RESTful, MQTT

VSAT MODEM SUPPORT

Modem protocols

Generic, OpenAMIP, OpenBMIP, Custom protocol

Modem hardware

SAILOR GX Modem

SAILOR GX MODEM UNIT (GMU)

Dimensions

1U 19” Rack Mount

HxWxD: 4.4 x 48 x 33 cm / 1.73” x 18.9” x 13”

Weight

3.5 kg / 7.7 lb

Humidity

EN60945 Protected, 95% (non-condensing)

IP class

IP30

Compass safe distance

0.4 m / 16” to EN60945

,QWHUIDFHV

[)&RQQHFWRUVƻIRU5[DQG7[WR%'8

1 x RJ-45 LAN connector for control and user data,

routes through BDU

1 x RS-422 (Modem Control)

1 x RS-232 Data (Modem Control)

1 x RS-232 Modem console

1 x Universal AC Power input

1 x Grounding bolt

Input power

100 – 240 VAC, 50-60 Hz, 90 W peak, 30 W typical

Modem interface (control)

OpenAMIP, OpenBMIP, RS-422 and RS-232

'LVSOD\

:HE00,2Q2໤VZLWFKDQGSRZHU/('

Temperature control

Built-in fan and heater

SYSTEM SPECIFICATIONS

Frequency band

Ka-band (Inmarsat GX-R2)

5HÀHFWRUVL]H

FP´

Type approvals

Inmarsat

&HUWL¿FDWLRQ

&RPSOLDQWZLWK&(0DULWLPH(76,)&&

System power supply range

100-240 VAC, 50-60 Hz

Total system power consumption 4.5W: 135 W typical, 185 W max (excl. Modem)

9.0W: 180 W typical, 215 W max (excl. Modem)

FREQUENCY BAND

17.7 to 20.2 GHz

27.5 to 30.0 GHz

ANTENNA CABLE & CONNECTORS

%'8WR$'8FDEOH

&RD[FDEOHIRU5[7[0R&$DQG'&SRZHURQ

a single cable

$'8FDEOHFRQQHFWRU

)HPDOH1&RQQHFWRUƻ

%'8FDEOHFRQQHFWRU

)HPDOH1&RQQHFWRUƻ

ABOVE DECK UNIT (ADU)

Antenna type, pedestal

3-axis stabilized tracking antenna with integrated

GNSS supporting GPS, GLONASS and Beidou

$QWHQQDW\SHUHÀHFWRUV\VWHP

5HÀHFWRUVXEUHÀHFWRUULQJIRFXV

Transmit Gain

43.6 dBi typ. @ 29.5 GHz (Incl. radome)

Receive Gain

39.1 dBi typ. @ 19.7 GHz (Incl. radome)

6\VWHP*7

G%.W\S#*+]DWHOHYDWLRQDQG

clear sky (incl. radome)

GX-R2 transceiver output

4.5W or 9.0W

EIRP

4.5W: 50.1 dBW typ. @ 29.5 GHz (incl. radome)

9.0W: 53.1 dBW typ. @ 29.5 GHz (incl. radome)

LNB

Inmarsat GX-R2 transceiver

Polarisation

Circular (RHCP, LHCP) independent controlled for Rx & Tx

Tracking receiver

Internal “all band/modulation type” including e.g.

power, DVB-S2X, GSC and modem RSSI

Satellite acquisition

Automatic - with and without Gyro/GPS Compass

input. Support for gyro free operation.

Elevation Range

-20° to +128°

Cross Elevation

-42° to +42°

Azimuth Range

Unlimited (Rotary Joint)

Ship motion, angular

Roll ±30° (6 sec), Pitch ±15° (5 sec), Yaw ±10° (8 sec)

Ship, turning rate and acceleration 15°/s and 15°/s2

ADU motion, linear

Linear acceler/-2.5 g max any direction

Vibration, operational

Sine: EN 60945 (8.7.2), DNV 2.4A, MIL-STD-167-1

(5.1.3.3.5). Random: Maritime

Vibration, survival

Sine: EN 60945 (8.7.2) dwell, MIL-STD-167-1

(5.1.3.3.5)

dwell.

Random: EN60721-3-6 class 6M3 mod. by EN60721-4-6

Shock

EN60721-3-6 class 6M3 mod. by EN60721-4-6.

MIL-STD-810F 516.5 (Proc. II),

Temperature (ambient)

Operational: -25°C to +55°C / -13°F to +131°F

Storage: -40°C to +85°C / -40°F to +185°F

Humidity 95%,

condensing

Rain / IP class

EN 60945 Exposed / IPx6

Wind

80 knots operational / 110 knots Survival

Ice, survival

25 mm

Solar radiation

1120 W/m2 to MIL-STD-810F 505.4

Compass safe distance

1.5 m / 59” (EN 60945)

Maintenance, scheduled

None

Maintenance, unscheduled

All modules, motor, RF parts and belts are replaceable

Built In Test

Power On Self-Test, Person Activated Self-Test and

Continuous Monitoring w. error logging

Dimensions (over all)

Height: H 91 cm / 36”

Diameter: Ø 82 cm / 32”

Weight

35 kg / 77 lb

71-178146-A01 01.22

For further information please contact:

[email protected]

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды