COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 87

Страница: 87 / 176

Settings

98-175666-C

Chapter 4: Setup of the antenna

4-27

IoT hub configuration

The IoT hub supports the monitoring solution from Cobham SATCOM where antenna

data are sent directly into the Cobham SATCOM IoT hub. This monitoring solution

requires a subscription.

Once the subscription has been purchased from Cobham SATCOM a list of IoT Keys will

be provided. Each IoT key is unique and will be bound to the antenna the first time it

connects. After a connection has been made, the IoT key cannot be used on other

antennas.
To enable IoT management on the page

IoT & Management

, do as follows:

1. Enter one of the provided IoT keys in the

IoT key

field.

2. Check the

IoT hub client

field.

3. For release 3.03 X.509 certificate and X.509 private key: you must manually upload

them to the antenna. Contact Cobham SATCOM to receive a valid certificate and

key.

4. Click

Apply

4.2.9 Dual antenna

For details how to set up Dual antenna operation see Appendix B,

Dual antenna

solution

4.2.10 User administration

In this section of the web interface you can configure the following administrative

settings:

•

To change a password

•

To set up permissions for guest user

Important

The IoT hub will not work without a subscription.
It is not possible to connect to the IoT hub or the data stream from

external systems.

Figure 4-19: Setup of the IoT hub

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды