COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 156

Страница: 156 / 176

98-175666-C

Appendix F: Event messages

F-8

List of events

08A03-0 ADM

WARNING GX Core Module

power

The Power Good signal from the Core Module is

low. The issue can either be: - Internal Core

Module or internal cable failure - Temperature

of Core Module is too high and it has been

turned off (*) - GMU has been manually

switched off on the front panel (*) (*) = Only on

systems with GMU. (!V,!T)

08A04-0 ADM

WARNING iDirect modem

The BDU detected a warning/error in the iDirect

modem. Log into the modem for more

information. Info: 0x00000001: Temperature

error 0x00000002: Test error 0x00000004:

Fan error (!V,!T)

08A05-0 ADM

WARNING GX Core Module

heating

The GX core module heater is active. It will

automatically be cleared when the core module

reaches the operational temperature level.

(!V,!T)

08B00-0 ADM

INFO

IoT med priority

msg rate exceeded.

The message rate limit has been reached for the

medium priority queue. The iothub client will

pause transmission of medium priority

messages for a short while.

08B01-0 ADM

INFO

IoT low priority msg

rate exceeded.

The message rate limit has been reached for the

low priority queue. The iothub client will pause

transmission of low priority messages for a

short while.

08B02-0 ADM

INFO

Iothub disabled

The iothub client has been disabled.

09000-0 KDM

ERROR

KDM 3V3 supply

Internal 3V3 voltage supply error in the KDM.

09001-0 KDM

ERROR

KDM 12V supply

Internal 12V voltage supply error in the KDM.

09002-0 KDM

ERROR

KDM display

Display hardware error in the KDM.

09010-0 KDM

ERROR

KDM link/SW

version

Link to the KDM module could not be

established. Either the KDM board is

malfunctioning, or - if the system software has

just been updated - the software is too old and

is not compatible with the KDM hardware.

0A080-0 Antenn

ERROR

EBUS loop

interrupted

EBUS communication error, loop interrupted.

0A081-0 Antenn

ERROR

ISCM error

Communication error with ISCM. Info:

0x00000001: Key line signal

0A100-0 Antenn

ERROR

ISCM Gyro

communication

Internal communication error on ISCM.

Module Type

Description

Explanation

Table F-1: Event messages (Continued)

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды