COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 176

background image

98-175666-C

Appendix B: Dual antenna solution

B-9

Dual antenna software upgrade procedure

B.4 Dual antenna software upgrade procedure

When making a software upgrade of a dual antenna system, it must be done in the

correct order to limit downtime of the VSAT service. It is recommended to do the

upgrade at a location where both antennas have connection to the satellite and are

outside blocking zones. In general a dual antenna system must have the same

software version in both antennas, otherwise a software mismatch warning will be

active on the system.
To make a software upgrade, do as follows:
1. Connect to the Slave BDU web server and upload the new software.
2. Wait for the Slave antenna system to reboot and to have finished its Power On Self-

Test (POST) and having connected to the Master antenna system again. The dual

antenna system might show a warning with software mismatch information.

3. Connect to the Master BDU web server and upload the new software.
4. Wait for the Master antenna system to reboot and finish its Power On Self-Test

(POST).

The dual antenna system should now be fully functional without any errors or

warnings present.

«
...
127
128
129
130
131
...
»

Содержание SAILOR XTR GX-R2

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAILOR XTR GX-R2

OMNIANGLE OA-144

Бренд: PAR Страницы: 4

ID ANT.U580/290-FCC

Бренд: Feig Electronic Страницы: 11

Бренд: DX Engineering Страницы: 8

Бренд: RFI Страницы: 4

Бренд: TRENDnet Страницы: 2

Бренд: Ventev Страницы: 2

Бренд: Sea Tel Страницы: 101

Бренд: One for All Страницы: 2

Бренд: Winegard Страницы: 2

Emerge HGA51G-DIR30

Бренд: Avocent Страницы: 2

Бренд: IKUSI Страницы: 2

Бренд: TAGSYS RFID Страницы: 23

Бренд: Hi-Z Antennas Страницы: 14

Бренд: Etek Navigation Страницы: 5

Бренд: etech components Страницы: 6

Бренд: Paradigm Страницы: 20

Бренд: Ubiquiti Страницы: 60

Бренд: US Robotics Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды