COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 128

Страница: 128 / 176

98-175666-C

Appendix B: Dual antenna solution

B-8

Configuration of the dual antenna solution

3. Go to Setting - Dual antenna page to set the antenna as master in dual

configuration.

B.3.6 To make an OTC for dual antenna systems

1. Make an azimuth calibration with both antenna systems (master and slave) using

manual azimuth calibration mode and one of the GX satellites,

Make sure you

have line-of-sight

2. Make a TX calibration for the master antenna system and for the slave antenna

system.

The entire dual antenna system is now ready for OTC.
1. Turn on the modem

power.

The first time the modem is turned on it will perform an OTC both on the master

and the slave antennas. During this process the modem will restart several times

before pointing towards the satellite and establish the link.

2. Be patient. The OTC procedure will take at least 16 minutes.

3. If for some reason you make a TX cable calibration again, the system will request

the operator to initiate a manual OTC procedure. You can start the OTC procedure

from the modem dashboard.

Figure B-8: Dual-antenna mode

Important

Do not power up the GMU at this point in time.

Important

Interrupting the process before it has completed will cause the

process to restart.

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды