COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 110

Страница: 110 / 176

Removal and replacement of the BDU

98-175666-C

Chapter 6: Service

6-2

6.1.2 LEDs in the BDU

The BDU has 3 LEDs: Power, Logon and Fail/Pass LED.

6.2 Removal and replacement of the BDU

There are no parts in the BDU that you can remove or replace. Contact your Cobham

SATCOM service partner for repair or replacement.

6.3 Removal and replacement of ADU modules

All replacement of modules must be done by a Cobham SATCOM service partner.

Before contacting your service partner check the LEDs on all modules (ACM, ISM and

motors).

Figure 6-1: BDU — LEDs

LED

Behavior

Description

Power

Steady green Power supply OK
Steady red

Power supply failure

Off

No power

Logon

Flashing

green

Current status is displayed:
• Searching satellite

• Identifying satellite

• Carrier lock & TX enabled from modem

Steady green Satellite link established
Off

No satellite link acquired

Fail/

Pass

LED

Steady red

A fault which prevents operation is present in the

system (ADU, BDU).

Flashing

green

A Power On Self Test (POST) or Self Test in progress.

The current status is displayed.

Flashing red

Active BITE failure or warning. The event is shown in the

BDU display.

Steady green No faults.

Table 6-2: LEDs on the BDU

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды