COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 126

Страница: 126 / 176

98-175666-C

Appendix B: Dual antenna solution

B-6

Configuration of the dual antenna solution

B.3.3 To configure the Slave BDU

The Slave BDU is configured to use the Master BDU as VSAT profile. The VSAT profile

must point to the IP address of the Master BDU, that is the IP address of the LAN port at

which the Master/Slave communication cable is connected.
1. Add a specific VSAT profile for dual antenna mode, go to

SETTINGS > VSAT

profiles

2. Add a profile, name it for example

ADU Slave

3. Select modem type

Master BDU

4. Set the IP address and netmask for the Slave BDU VSAT profile to match the subnet

of the Master BDU.

5. Enter the IP address of the master BDU. IP addresses for the master and slave must

be in the same subnet. Recommended network settings are shown in the following

figure.

6. Click the save icon to save the VSAT profile.
7. Click

SETTINGS > VSAT profiles

8. Click

Activate

to activate the VSAT profile

ADU Slave

B.3.4 Blocking zone setup for dual antenna setup

It is recommended to define the following 3 blocking zones in each SAILOR XTR GX-R2

system:
1. Actual blocking zones on the vessel (No TX)
2. Switching blocking zones (TX allowed)
3. Personnel safety zones (No TX)

Figure B-6: Slave BDU VSAT profile

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды