COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 125

Страница: 125 / 176

98-175666-C

Appendix B: Dual antenna solution

B-5

Configuration of the dual antenna solution

• When signal strength drops 4 dB lower than the in-active antenna.

B.3.2 To configure the Master BDU

The configuration of the master BDU depends on which ports are used and how your

network has been configured.

Configure the Master BDU VSAT profile exactly the same way as a single SAILOR XTR

GX-R2 system. Recommended network settings are shown in the following figure.

After the Master BDU has been configured, do as follows:
1. Click

SETTINGS > Dual antenna

2. Select

Set this antenna as master in dual configuration

and click

Apply

3. Dual antenna mode, select Automatic Dual Mode.
4. If needed, click Switch to the other antenna in the dual antenna system.

Important

Before you enable dual mode, set up the master and the slave to be on

the same subnet but with different IP addresses.

Figure B-4: Master BDU, Network settings

Figure B-5: Enabling dual-antenna mode in the Master BDU

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды