COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 38

Страница: 38 / 176

Installation of the ADU (S1000 antenna)

98-175666-C

Chapter 2: Installation

2-17

2.3 Installation of the ADU (S1000 antenna)

The following sections describe the installation and grounding of the ADU. The ADU is

shipped fully assembled. Install it on the mast and attach the ADU cable.

2.3.1 To install the ADU

Prerequisites

• Ensure that the crane hook has a closing mechanism to prevent accidental

slippage of the lifting straps.

• Mount the antenna as far away as possible from the shipʼs radar and high power

radio transmitters, read more in

Interference from radar, GPS/GNSS, L-band and

other transmitters

on page 2-13.

• Install the ADU at a location where

vibrations are limited to a minimum

• Make sure that there is sufficient space underneath the ADU to open the service

hatch.

•

Important

Maintain the vertical orientation of the ADU center line

WARNING!

Use a strong webbed sling with a belt to lift the ADU without

damaging the radome. Make sure that the sling can carry

105 kg.

WARNING!

The ADU may be subject to swaying motions in windy

conditions. Always use tag lines to stabilize the ADU during

hoisting. It is the crane operatorʼs responsibility to

determine whether the environmental conditions are

suitable for a safe lift.

Figure 2-15: Use of strong sling with a belt and tag lines for safe hoisting

Webbed sling with belt

Tag lines

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды