COBHAM SAILOR XTR GX-R2 Скачать руководство пользователя страница 146

Страница: 146 / 176

98-175666-C

Appendix E: Grounding and RF protection

E-7

Grounding Recommendations

illustration below. The crimp terminals must be a marine approved type e.g. the

DuraSeal series from Raychem.

Ground cable - connection

Mount the ground cable close to and parallel to the shielded coax cable thus

minimizing ground loop problems. If possible, route the coax cable and the ground

cable in metal conduits bonded to the hull or within a mast (depending on the actual

installation).
The ground cable must be connected at one of the mounting/grounding bolts on the

ADU. Use bolts and washers of stainless steel and seal the joint with protective coating

to avoid corrosion. If the ADU is to be isolated from the mounting base, shoulder

bushings and washers must be used — see figure E-7,

Isolation of the ADU from the

mounting base

on page E-8.

At the other end, connect the ground cable as described in

To ground the BDU

page E-2.

Isolation of the ADU from the mounting base

In cases where the ADU is to be isolated from the mounting base, shoulder bushings

and washers (accessories) must be used as illustrated below. Please note that the

Figure E-6: Separate ground cable

Antenna:

M12 Insulated Ring Terminal
(Raychem, DuraSeal Series )

Terminal:

Appropriate size
Insulated Ring Terminal
(Raychem, DuraSeal Series )

Содержание SAILOR XTR GX-R2

















































































































































































Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды

COBHAM SAILOR XTR GX-R2, Руководство по установке

Результаты поиска

Содержание SAILOR XTR GX-R2

Отзывы:

Похожие инструкции для SAILOR XTR GX-R2

Бренды по названию

Популярные бренды