Club Car IQ PLUS 2008 Скачать руководство пользователя страница 24

Страница: 24 / 164

ELECTRICAL SYSTEM AND TESTING

Troubleshooting

Page 11-10

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

Monitor Menu – MAIN CONT (solenoid)
does not indicate ON when the
solenoid should be activated.

Diagnostic Menu – MAIN CONT DNC
(main contactor (solenoid) did not
close) fault code

Speed controller logic malfunction

Disconnect the batteries and discharge
the controller.

See Disconnecting The

Batteries on page 10-3.

Reconnect the

batteries and see if the symptom returns.

Failed controller FET (that powers up
solenoid coil)

Loose, broken, or disconnected wire(s) at
solenoid or B+ speed controller terminal

Repair and/or connect the loose or
disconnected wire(s)

Loose or disconnected 24-pin connector
at speed controller or broken wire

Repair and/or connect the 24-pin
connector to the speed controller

Failed solenoid

Replace solenoid.

See Solenoid

Removal, Section 13, Page 13-8.

Monitor Menu – KEY INPUT does not
indicate ON when key switch is in the
ON position

Loose or disconnected wires at key switch
terminals or broken wire

Repair and/or connect the quick
disconnect terminals to the Forward/
Reverse switch

Loose or disconnected 24-pin connector
at speed controller or broken wire

Repair and/or connect the 24-pin
connector to the speed controller

Failed key switch

Test Procedure 9 – Key Switch and
MCOR Limit Switch Circuit on page 11-23

Diagnostic Menu – THROTTLE FAULT 1
fault code

Loose or disconnected three-pin
connector at the MCOR or broken wire

Repair and/or connect the three-pin
connector to the MCOR

Loose or disconnected 24-pin connector
at speed controller or broken wire

Repair and/or connect the 24-pin
connector to the speed controller

Diagnostic Menu – THROTTLE FAULT 1
fault code, continued

Failed MCOR

Test Procedure 4 – MCOR Voltage on
page 11-18

Diagnostic Menu – HW FAILSAFE
(Hardware Failsafe) fault code

Armature drive FET’s (field-effect
transistors) inside speed controller have
failed

Replace the speed controller.

See Speed

Controller Removal, Section 13,
Page 13-11.

Speed controller logic malfunction

Disconnect the batteries and discharge
the controller.

See Disconnecting The

Batteries on page 10-3.

Reconnect the

batteries and see if the symptom returns.

Diagnostic Menu – MAIN WELDED
(main solenoid contacts welded) fault
code

solenoid contacts have failed closed

Replace solenoid.

See Solenoid

Removal, Section 13, Page 13-8.

Diagnostic Menu – MAIN DRIVER ON or
MAIN DRIVER OFF fault code

Speed controller logic malfunction

Disconnect the batteries and discharge
the controller.

See Disconnecting The

Batteries on page 10-3.

Reconnect the

batteries and see if the symptom returns.

Failure of the FET that controls the
solenoid coil

Replace the speed controller.

See Speed

Controller Removal, Section 13,
Page 13-11.

Diagnostic Menu – MAIN COIL FAULT
fault code

Diagnostic Menu – MAIN DROPOUT
fault code

Solenoid coil has failed in an open
condition or broken wire to solenoid coil

Replace solenoid.

See Solenoid

Removal, Section 13, Page 13-8.

Troubleshooting Guide continued on next page...

TROUBLESHOOTING GUIDE 1

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Содержание IQ PLUS 2008





































































































































































Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды

Club Car IQ PLUS 2008, Дополнение к руководству по обслуживанию и ремонту

Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды