Club Car IQ PLUS 2008 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 164

background image

BATTERIES

Battery Testing

Page 14-14

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

14

BATTERY TROUBLESHOOTING EXAMPLES

The following information represents a few examples of troubleshooting battery problems.

Example 1

Vehicle no. 68 was suspected of having a bad battery due to its performance. As a result, the battery charger
test was performed. After a full charge, the battery charger ammeter read 8.0 amps. Next, the on-charge volt-
age test was performed and the following results were recorded:

*Battery no. 3 appears suspect. Batteries no. 1 and 4 are also suspect. Next, a hydrometer test should be
conducted on all batteries.

Hydrometer test results:

*After the hydrometer test, it appears that battery no. 1 is the problem. Next, the discharge test was per-
formed.

Discharge test results:

*After a discharge test which lasted 45 minutes, battery no. 1 is clearly shown to be the problem. Battery no.
4 should be watched a little more closely but appears to be okay. Battery no. 1 should be replaced with a bat-
tery that has about the same age and usage as the other batteries in the set.

Example 2

Vehicle no. 70 was also suspected of having a bad battery due to its performance. The battery charger test
showed 7.0 amps after a full charge. After confirming there were no problems with the electrical system,
charger or brakes, the on-charge voltage was recorded as follows:

*Battery no. 2 was immediately suspected as the problem. After checking battery no. 2 with a hydrometer, it
was discovered that the negative post cell was completely dead. Battery no. 2 should be replaced with a bat-
tery that has the same age and usage as the other batteries in the set.

BATTERY NO.

1

2

3

4

5

6

7

8

On-Charge Voltage

7.40 V

7.60 V

7.10* V

7.40 V

7.70 V

7.80 V

7.80 V

7.80 V

CELL NUMBER

BATTERY NUMBER

1

2

3

4

5

6

7

8

Cell 1 (Positive Post)

1.200*

1.265

1.300

1.250

1.280

1.260

1.260

1.260

Cell 2

1.285

1.275

1.290

1.270

1.295

1.265

1.265

1.265

Cell 3 (Negative Post)

1.265

1.270

1.275

1.265

1.280

1.275

1.275

1.275

BATTERY NO.

1

2

3

4

5

6

7

8

Discharge Voltage

3.80* V

5.25 V

5.65 V

5.25 V

5.50 V

5.60 V

5.70 V

5.30 V

BATTERY NO.

1

2

3

4

5

6

7

8

On-Charge Voltage

7.40 V

7.10* V

7.45 V

7.6 V

7.65 V

7.50 V

7.55 V

7.65 V

«
...
114
115
116
117
118
...
»

Содержание IQ PLUS 2008





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IQ PLUS 2008

Бренд: Braun Страницы: 134

Бренд: Remington Страницы: 143

Chopper GMT264GB

Бренд: Conair Страницы: 2

Бренд: EINHELL Страницы: 52

SERIES 3 340S-4

Бренд: Braun Страницы: 18

Бренд: Melissa Страницы: 12

Бренд: Sunred Страницы: 15

Бренд: Braun Страницы: 51

Oral-B Pro TriZone

Бренд: Braun Страницы: 16

Бренд: Trotec Страницы: 8

Oral-B GENIUS X

Бренд: Braun Страницы: 154

Бренд: Mr. Heater Страницы: 16

Super Nimbus V12 Series

Бренд: Sawo Страницы: 6

MINIDRAGON MN-23NB-DRF

Бренд: Sawo Страницы: 28

HEATERKING ROUND DRFT12-150Ni

Бренд: Sawo Страницы: 31

Бренд: EdenPURE Страницы: 35

Бренд: Tylo Страницы: 30

Бренд: cecotec Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды