background image

PERIODIC MAINTENANCE

General Information

Page 10-4

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

10

GENERAL INFORMATION

To ensure trouble-free vehicle performance, it is very important to follow an established preventive mainte-
nance program. Regular and consistent vehicle maintenance can prevent vehicle downtime and expensive
repairs that can result from neglect. Any vehicle not functioning correctly should be removed from use until it
is properly repaired. This will prevent further damage to the vehicle and avoid the possibility of injury due to
unsafe conditions.
Contact your local Club Car distributor/dealer to perform all repairs and semiannual and annual periodic ser-
vice.

PERIODIC SERVICE SCHEDULE

ý 

WARNING

• Service, repairs, and adjustments must be made per instructions in the appropriate

maintenance and service manual and this supplement.

• If any problems are found during scheduled inspection or service, do not operate the vehicle

until repairs are made. Failure to make necessary repairs could result in fire, property
damage, severe personal injury, or death.

NOTE: 

If the vehicle is constantly subjected to heavy use or severe operating conditions, the preventive
maintenance procedure should be performed more often than recommended in the periodic ser-
vice and lubrication schedules.
Both the Periodic Service Schedule 
and the Periodic Lubrication Schedule must be followed to
keep vehicle in optimum operating condition.

Содержание IQ PLUS 2008





































































































































































Отзывы: