Club Car IQ PLUS 2008 Скачать руководство пользователя страница 124

Страница: 124 / 164

MOTOR (MODEL DA5-4006)

Motor

Page 16-4

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

MOTOR DISASSEMBLY

1. Release the clasp and remove the headband assembly (21) from the motor. Visually inspect brushes and

springs.

(Figure 16-13, Page 16-10)

2. Before continuing disassembly, place match marks on the motor end cap (20) and motor frame (14).

3. Remove speed sensor (10) and magnet (12).

3.1. Remove the two screws (11) that secure the speed sensor (10) to the end cap (20).
3.2. Remove the bolt (13) securing the magnet (12) to the armature shaft (15). Hold the back of the

armature assembly to keep it from turning as you remove the bolt.

3.3. Inspect the speed sensor magnet.

See Speed Sensor Magnet Inspection on page 16-9.

4. Orient the motor so that the splined end of the armature is facing down.

5. Remove the four end cap bolts. The weight of the motor housing will cause it to drop when the bolts are

removed. See following Caution.

CAUTION

• The motor housing will drop when the bolts are removed. Do not put fingers under the motor

Figure 16-4 Speed Sensor Magnet

Figure 16-5 End Cap Removal

Figure 16-6 Brush Springs Positioning

Figure 16-7 Armature Removal

Содержание IQ PLUS 2008





































































































































































Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды

Club Car IQ PLUS 2008, Дополнение к руководству по обслуживанию и ремонту

Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды