Club Car IQ PLUS 2008 Скачать руководство пользователя страница 44

Страница: 44 / 164

ELECTRICAL SYSTEM AND TESTING

Troubleshooting

Page 11-30

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

Test Procedure 10C – Pin 8
See General Warning, Section 10, Page 10-1.

Pin 8 in the 24-pin connector provides a connection point for the MCOR limit switch to the speed controller.

1. Disconnect the batteries and discharge the controller.

See Disconnecting The Batteries on page 10-3.

2. Place chocks at the front wheels and lift the rear of the vehicle with a chain hoist or floor jack. Position

jack stands under the frame crossmember between the spring mount and side stringer, just forward of
each rear wheel.

See WARNING “Lift only one end...” in General Warning, Section 10, Page 10-1

3. Disconnect the 24-pin connector at the speed controller.

4. Set a multimeter to 200 volts DC, insert the red (+) probe of the multimeter into pin 8 (green wire) of the

24-pin connector.

See following CAUTION.

Using an alligator clip, connect the black (–) probe to the B–

terminal of the speed controller

(Figure 11-20, Page 11-30)

CAUTION

• Do not fully insert probes into the 24-pin plug. Doing so can result in a poor connection.

5. Place the Tow/Run switch in the TOW position and connect the battery cables, positive (+) cable first.

Tighten battery terminals to 110 in-lb (12.4 N·m).

6. Place the Tow/Run switch in the RUN position, key switch in the ON position, and Forward/Reverse

switch in the FORWARD or NEUTRAL position.

7. The multimeter should indicate zero volts DC at this time.

8. While monitoring the multimeter, slowly press the accelerator pedal and hold the pedal at approximately

20% of full travel.

9. After a short delay, the onboard computer should power-up (come out of sleep mode).

10. The multimeter should indicate full battery voltage (approximately 48 volts) when the accelerator pedal

is pressed.

11. While observing the multimeter, release the accelerator pedal.

Figure 11-20 Test: Pin 8 (Green Wire)

Detail:
Front of 24-Pin Connector

Содержание IQ PLUS 2008





































































































































































Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды

Club Car IQ PLUS 2008, Дополнение к руководству по обслуживанию и ремонту

Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды