Club Car IQ PLUS 2008 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 164

background image

IQ DISPLAY MODULE (IQDM) SERIES 2 AND IQDM-P DIAGNOSTICS

IQDM and IQDM-P Handset Troubleshooting

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

Page 12-19

12

IQDM AND IQDM-P HANDSET TROUBLESHOOTING

In the event that the handset does not function as described in this manual, the following troubleshooting
guide should be studied and the referenced test procedures should be performed to troubleshoot the IQDM
and IQDM-P Series 2 handsets.

TROUBLESHOOTING GUIDE

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Handset display screen is blank

Handset cord and/or adaptor is
disconnected

See Plugging the Handset into the
Vehicle on page 12-1.

Vehicle batteries – loose terminals or
corrosion

See Section 14 – Batteries.

Vehicle batteries – improperly wired

See Section 14 – Batteries.

Vehicle batteries – batteries failed

See Section 14 – Batteries.

Vehicle batteries – batteries not fully
charged

See Section 14 – Batteries.

Handset cord has failed

Test Procedure 1 – Handset Cord on
page 12-20

Handset cord adaptor has failed

Test Procedure 2 – Handset Cord Adaptor
on page 12-20

IQDM jack (on vehicle) has failed

Test Procedure 3 – IQDM Jacks on
page 12-21

Contrast Setting is too light

See Program on page 12-18.

Onboard computer is in power-down
mode

Drive the vehicle for a short distance and
reconnect the handset to the vehicle.

Onboard computer malfunction

See Section 11 – Electrical System and
Testing.

Loose vehicle wire harness connections

Test Procedure 3 – IQDM Jacks on
page 12-21

Speed controller malfunction

See Section 11 – Electrical System and
Testing.

Handset has failed

Replace handset

Display screen shows jumbled or
undecipherable characters

Speed controller malfunction

See Section 11 – Electrical System and
Testing.

Handset malfunction

Disconnect the IQDM cord from the
vehicle. Wait a few seconds and
reconnect the handset to the vehicle

Loose connection at IQDM jack

Test Procedure 3 – IQDM Jacks on
page 12-21

Intermittent handset cord failure

Test Procedure 1 – Handset Cord on
page 12-20

Intermittent handset cord adaptor failure

Test Procedure 2 – Handset Cord Adaptor
on page 12-20

Loose vehicle wire harness connections

Test Procedure 3A – IQDM Jack (Located
Under the Instrument Panel) on
page 12-21

Troubleshooting Guide continued on next page...

«
...
79
80
81
82
83
...
»

Содержание IQ PLUS 2008





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IQ PLUS 2008

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 2

Cook Expert Steamer XL

Бренд: MAGIMIX Страницы: 80

Бренд: Orbegozo Страницы: 89

Бренд: Linea 2000 Страницы: 40

Бренд: Wilfa Страницы: 35

Бренд: Trotec Страницы: 13

Бренд: Trotec Страницы: 19

Бренд: Verona Страницы: 24

Бренд: Frico Страницы: 11

Бренд: Jetpik Страницы: 18

Flex360 Degrees XR1410

Бренд: Remington Страницы: 180

Бренд: Remington Страницы: 19

Бренд: Xiu Solution Страницы: 8

Бренд: Malmbergs Страницы: 8

Бренд: TurMix Страницы: 7

Бренд: Panasonic Страницы: 2

Astra Steamer Hybrid

Бренд: Idromatic Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды