Club Car IQ PLUS 2008 Скачать руководство пользователя страница 147

Страница: 147 / 164

TRANSAXLE (TYPE G)

Transaxle Installation

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

Page 17-11

3. Install the two U-bolts, jounce bumper mount (if required), and spacers, lockwashers, and nuts. Tighten

the nuts to 25 ft-lb (34 N·m). Tighten the U-bolt nuts so an equal amount of thread is visible on each leg
of the bolt.

4. Install the motor.

See Motor Installation, Section 16, Page 16-12 or Motor Installation, Section 16,

Page 16-12.

5. If using a chain hoist, lower the vehicle while guiding the leaf springs into the rear spring shackles. If

using a floor jack, raise the differential while guiding the leaf springs into the rear spring shackles. Then
raise the jack stands to support the transaxle.

6. Connect the four motor wires. Tighten the retaining nuts to 65 in-lb (7.3 N·m). Use two wrenches to pre-

vent the posts from turning.

See following NOTE.

NOTE:

If the motor wires were not tagged when disconnected, refer to the wiring diagram for proper con-
nection.

See Wiring Diagrams, Section 11, Page 11-2.

7. Insert bolts through the spring shackles and bushings in the leaf spring eyes. Secure bolts with locknuts.

Tighten to 15 ft-lb (20.3 N·m).

8. Connect the brake cables using new bow tie pins (1)

(Figure 17-7, Page 17-5)

9. Install the shock absorbers. Tighten shock absorber retaining nuts until the rubber bushings expand to

the same size as the cup washers.

10. Install the rear wheels and finger-tighten the lug nuts.

11. Lift the vehicle and remove the jack stands.

12. Lower vehicle and tighten the lug nuts, using a crisscross pattern, to 55 ft-lb (74.6 N·m).

13. Inspect the vehicle to check for proper operation.

See following WARNING.

WARNING

• Make sure that the vehicle operates in the forward direction when the Forward/Reverse switch

is in the FORWARD position.

• Make sure that the vehicle operates in the reverse direction when the Forward/Reverse switch

is in the REVERSE position. The reverse buzzer will sound as a warning when the Forward/
Reverse switch is in REVERSE.

• Make sure that the vehicle does not operate when the Forward/Reverse switch is in the

NEUTRAL position.

Содержание IQ PLUS 2008





































































































































































Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды

Club Car IQ PLUS 2008, Дополнение к руководству по обслуживанию и ремонту

Результаты поиска

Содержание IQ PLUS 2008

Отзывы:

Похожие инструкции для IQ PLUS 2008

Бренды по названию

Популярные бренды