Club Car IQ PLUS 2008 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 164

background image

IQ DISPLAY MODULE (IQDM) SERIES 2 AND IQDM-P DIAGNOSTICS

Introductory Display

Page 12-2

2008-2011 IQ Plus Electric Vehicle Maintenance and Service Supplement

12

INTRODUCTORY DISPLAY

Immediately after the handset is connected to the vehicle, it begins loading the vehicle speed controller infor-
mation. After a few seconds, the screen displays the following menu items:

•

Program (IQDM-P)

•

Monitor

•

Faults

•

Functions

•

Information

•

Programmer Setup

In the event that the handset does not display any information, or the screen is difficult to read, refer to the
IQDM Series 2 troubleshooting procedures.

See IQDM and IQDM-P Handset Troubleshooting on

page 12-19.

MENU NAVIGATION

The NAVIGATION BUTTON is the four-arrow button located on the left side of the handset

(Figure 12-2,

. This button is used to navigate through and select menus. Pressing the up or down arrows allows

the user to scroll through the menu items. When the box beside the desired menu is blinking, pressing the
right arrow selects that menu item. Pressing the left arrow allows the user to go back one screen.

The CHANGE VALUE BUTTON is the button located on the right side of the handset

(Figure 12-2, Page 3)

This button allows the user to change values by pr or –.

The three yellow buttons labeled 1, 2 and 3 are BOOKMARK BUTTONS

(Figure 12-2, Page 3)

. These but-

tons allow the user to bookmark up to three specific screens for rapid return to those screens. To bookmark a
specific display screen, have the desired screen displayed and simply press and hold a bookmark button until
the statement “bookmark set” is displayed. When it is necessary to go back to the bookmarked screen, rapidly
press and release the appropriate bookmark button.

See following NOTE.

NOTE:

When going to a bookmarked display screen, be sure to rapidly press and release the button. If the
button is pressed and held for too long, the bookmark will be overridden with the current screen.

The three yellow buttons also allow for quicker input of serial number and car decal number. Press and hold
“+” or “-” while holding buttons 1, 2 or 3 to accelerate a number search.

The following menus are accessible on the IQDM Series 2 handset:

Program (IQDM-P only)

The

program

menu allows the user to view and change custom speed controller settings.

See Program

Menu, Section 18, Page 18-2.

Monitor

The

monitor

menu displays values for certain parameters to facilitate speed controller troubleshooting.

Monitor Menu on page 12-4.

«
...
62
63
64
65
66
...
»

Содержание IQ PLUS 2008





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IQ PLUS 2008

Бренд: Wahl Страницы: 168

Бренд: thermalpanel Страницы: 10

Бренд: Comfort Glow Страницы: 12

TRIZONE 5000 SERIES

Бренд: Oral-B Страницы: 61

Бренд: Flagro Страницы: 15

Бренд: Melissa Страницы: 12

Бренд: Red Bull Racing Страницы: 52

Бренд: Whirlpool Страницы: 47

Ultraheat S 3004

Бренд: Truma Страницы: 9

Бренд: Creda Страницы: 14

Бренд: Somogyi Страницы: 12

Бренд: Somogyi Страницы: 25

Бренд: HELLER Страницы: 5

Бренд: HELLER Страницы: 8

Бренд: Remington Страницы: 10

Бренд: Market Forge Industries Страницы: 18

Бренд: Bartscher Страницы: 13

Бренд: Bartscher Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды