manualshive.com logo in svg

Cisco ONS 15454, Руководство по установке оборудования

Поделиться
Скачать
Cisco ONS 15454 Скачать руководство пользователя страница 467

Filter Bracket (Front Door Removed), on page 438

shows the fan-tray air filter in an external filter bracket on

an ETSI shelf.

Step 2

If the filter is installed below the fan tray and not in the external filter brackets, open the front door of the
shelf assembly. If the front door is already open, proceed to Step 3.

a) Open the front door lock.

The ONS 15454 comes with a pinned hex key for locking and unlocking the front door. Turn the key
counterclockwise to unlock the door and clockwise to lock it.

b) Press the door button to release the latch.
c) Swing the door open.

Step 3

(Optional) Remove the front door using the

DLP-G10 Remove the Front Door , on page 58

. If you do not

want to remove the door or it is already removed, proceed to Step 4.

Figure 287: ANSI Shelf Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed)

Cisco ONS 15454 Hardware Installation Guide

437

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G114 Inspect and Replace the Air Filter

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды