Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 476 / 516

background image

None

Security Level

Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do
not view directly with optical instruments. Viewing the laser output with certain optical instruments
(for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye
hazard.

Statement 1056

Warning

Procedure

Step 1

Using an inspection microscope, inspect each fiber connector for dirt, cracks, or scratches.

Step 2

Replace any damaged fiber connectors.

Replace all dust caps whenever the equipment is unused for 30 minutes or more.

Note

Step 3

Complete the

DLP-G262 Clean Fiber Connectors with CLETOP, on page 447

as necessary.

Step 4

Complete the

DLP-G263 Clean the Fiber Adapters, on page 447

as necessary.

To clean multi-fiber optic connectors, complete the

DLP-G261 Clean Multi Fiber-Optic Cable

Connectors, on page 446

as necessary.

Note

Stop. You have completed this procedure.

DLP-G261 Clean Multi Fiber-Optic Cable Connectors

This task cleans the multi fiber optic connectors

Purpose

Cleaning Cartridge for multi fiber optic connectors

Tools/Equipment

None

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams
or view directly with optical instruments.

Statement 1051

Warning

Procedure

Step 1

Remove the protective cap on the optical fiber cable connector.

Cisco ONS 15454 Hardware Installation Guide

446

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

DLP-G261 Clean Multi Fiber-Optic Cable Connectors

«
...
474
475
476
477
478
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: WP Страницы: 30

PXI Express PXIe-1071

Бренд: National Instruments Страницы: 65

Supero SC731 Series

Бренд: Supermicro Страницы: 36

Бренд: WP Страницы: 32

Бренд: AXIOMTEK Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды