Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 48 / 516

background image

Definition

Symbol Color/Shape

Cross-connect (XC/XCVT/XC10G) slot, Slots 8 and 10. Only install ONS 15454 cards
with a cross symbol on the faceplate.

Cross-connect cards are not required in DWDM applications. Install a
FILLER card or blank card if not using Slots 8 and 10.

Note

Green/Cross

Protection slot in 1:N protection schemes.

Red/P

AIC/AIC-I slot, Slot 9. Only install cards with a diamond symbol on the faceplate.

Red/Diamond

Slots 1 to 4 and 14 to 17. Only install cards with a star symbol on the faceplate.

Gold/Star

(Only used with the 15454-SA-HD shelf assembly.) Slots 3 and 15. Only install ONS
15454 ANSI cards with a blue hexagon symbol on the faceplate.

Blue/Hexagon

ONS 15454 M2

The ONS 15454 M2 shelf assemblies have 3 card slots numbered sequentially from bottom to top. Slot 1 is
reserved for control cards (TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE). Slot 2 and Slot 3 are dedicated
for common line cards.

The ONS 15454 M2 shelf must be equipped with a TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE card.

Caution

Shelf slots have symbols indicating the type of cards that you can install in them. Each ONS 15454 M2 card
has a corresponding symbol. The symbol on the card must match the symbol on the slot.

Figure 5: Slot Symbols

The following table shows the slot and card symbol definitions.

Table 4: Slot and Card Symbols

Definition

Symbol Color/Shape

Slot 1. TNC/TNCE/TSC/TSCE/TNCS-2/TNCS-2O card slot. Only install the card
with a square symbol on the faceplate.

Purple/Square

Slots 2 and 3. Only install cards with a circle symbol on the faceplate.

Orange/Circle

Slots 2 to 3. New line cards with high speed back plane connectors.

Orange/Hollow Circle

Slots 2 and 3. New Uplink card.

Pink/Pentagon

Cisco ONS 15454 Hardware Installation Guide

18

Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

ONS 15454 M2

«
...
46
47
48
49
50
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: SilverStone Страницы: 12

5C105 MATRIX E5

Бренд: Enterasys Страницы: 40

Echo Express SE III

Бренд: Sonnet Страницы: 14

Echo Express III-D Thunderbolt 3 Edition

Бренд: Sonnet Страницы: 14

echo express SE II

Бренд: Sonnet Страницы: 16

Echo Express SE I

Бренд: Sonnet Страницы: 16

Бренд: Yeong Yang Страницы: 4

Бренд: Honeywell Страницы: 276

ExpressBox 3600

Бренд: Magma Страницы: 2

Бренд: Supermicro Страницы: 91

Бренд: Juniper Страницы: 149

Night Shark RGB

Бренд: Sharkoon Страницы: 10

Бренд: Supermicro Страницы: 29

Бренд: Supermicro Страницы: 31

Бренд: Supermicro Страницы: 37

Бренд: Supermicro Страницы: 40

Бренд: Supermicro Страницы: 31

Бренд: Supermicro Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды