Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 325 / 516

background image

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 40A and between -40.5 VDC to -57.6 VDC.

Statement

1005

Warning

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: 10A-20A, 100-240 VAC~.

Statement 1005

Warning

To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of: 131°F (55°C).

Statement 1047

Warning

Take care when connecting units to the supply circuit so that wiring is not overloaded.

Statement 1018

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:

Warning

•

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with
the heaviest component at the bottom of the rack.

•

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack.

Statement 1006

To prevent airflow restriction, allow clearance around the ventilation openings to be at least:1 inch
(25.4 mm)

Statement 1076

Warning

Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M6 shelf as shown
in

Figure 1: 19-inch ANSI Rack Post Recommended for Cisco ONS 15454 M6 and M2 Shelves, on page 3

Note

To comply with EN50121-4:2006 - Railway applications, Electromagnetic compatibility, a shielded
cable must be used to connect to the EMS port. This cable must be less than 30 meters in length and
not placed in the 3 meter boundary, as defined in EN50121-4:2006, Table 2, note 1.

Statement 8010

Warning

To comply with EN50121-4:2006 - Railway applications, Electromagnetic compatibility, DC power
cables must be less than 30 meter long.

Statement 8011

Warning

Cisco ONS 15454 Hardware Installation Guide

295

Installing the ONS 15454 M6 Shelf

NTP-G252 Install the ONS 15454 M6 Shelf

«
...
323
324
325
326
327
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: TYAN Страницы: 194

Apollo 4510 Gen10

Бренд: HP Страницы: 74

Бренд: HP Страницы: 99

Бренд: LG Страницы: 16

Бренд: HDanywhere Страницы: 30

Supero SC933E1-R760B

Бренд: Supermicro Страницы: 84

Supero SC933 Series

Бренд: Supermicro Страницы: 84

OSS-PCIE-4UV-5-1

Бренд: OSS Страницы: 90

Бренд: Netstor Страницы: 10

SYMKLOUD MS2900

Бренд: Kontron Страницы: 28

MCT-RACK-12-MGM

Бренд: CTS Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды