Cisco ONS 15454 Скачать руководство пользователя

Страница: 250 / 516

Step 3

Swing the door open.

Figure 140: Cisco ONS 15454 M2 Standard Door—Opened

Step 4

Return to your originating procedure (NTP).

DLP-G595 Remove the Standard Door of the ONS 15454 M2 Shelf

This task removes the standard door of the ONS 15454 M2 system.

Purpose

#2 Phillips Dynamometric screwdriver

Tools/Equipment

•

DLP-G594 Open the Standard Door of the ONS 15454 M2 Shelf, on page
219

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the

Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Procedure

Step 1

Unscrew the nut holding the ground cable to the shelf. Remove the nut.

Step 2

Remove the ground cable from the shelf as shown in the following figure

Cisco ONS 15454 Hardware Installation Guide

220

Installing the ONS 15454 M2 Shelf

DLP-G595 Remove the Standard Door of the ONS 15454 M2 Shelf

Содержание ONS 15454




































































































































































































































































































































































































































































































































Результаты поиска

Содержание ONS 15454

Отзывы:

Похожие инструкции для ONS 15454

Бренды по названию

Популярные бренды

Cisco ONS 15454, Руководство по установке оборудования

Результаты поиска

Содержание ONS 15454

Отзывы:

Похожие инструкции для ONS 15454

Бренды по названию

Популярные бренды