Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 157 / 516

background image

Procedure

Step 1

The Y-cable module tray requires 1 RU in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack. Locate
the RMU space specified in your site plan. Use the Cisco TransportPlanner Internal Connections Report to
determine how many Y-cable modules you need to install.

Step 2

Verify that the mounting brackets attached to the unit are correct for your rack size. Complete

the Mounting Bracket to Fit a 19-inch (482.6-mm) Rack (ANSI Only), on page 33

as required.

Step 3

Align the chassis with the rack mounting screw holes, insert the four screws, and tighten.

Step 4

Return to your originating procedure (NTP).

DLP-G30 Install the FlexLayer Shelf

This task installs the FlexLayer shelf. Perform this task if you are installing any
FlexLayer modules.

Purpose

#2 Phillips Dynamometric screwdriver

FlexLayer shelf (15216-FL-SA)

#14 AWG wire (minimum) for frame grounding

Tools/Equipment

None

Prerequisite
Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Procedure

Step 1

The FlexLayer shelf requires 1 RU in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack. Locate the
RMU space specified in your site plan.

Step 2

A set of mounting brackets are included with the FlexLayer mounting kit, one set each for 19-inch (482.6-mm)
or 23-inch (584.2-mm) racks. Verify that your chassis is equipped with the correct set of brackets for your
rack. Change the brackets as required.

Step 3

Align the chassis with the rack mounting screw holes; one at a time, insert and tighten the three screws.

Step 4

Connect a frame ground to the ground terminal provided on either side of the chassis. Use minimum #14
AWG wire.

Step 5

Repeat this task as necessary for each FlexLayer shelf you want to install.

Step 6

Return to your originating procedure (NTP).

Cisco ONS 15454 Hardware Installation Guide

127

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

DLP-G30 Install the FlexLayer Shelf

«
...
155
156
157
158
159
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: StarTech.com Страницы: 10

Бренд: Intel Страницы: 1

Бренд: Comet Models Страницы: 2

1U Rackmount Chassis Kit R10-A2P4

Бренд: Asus Страницы: 34

Бренд: Cisco Страницы: 24

AS5350 - Universal Access Server

Бренд: Cisco Страницы: 262

Бренд: IBM Страницы: 140

Бренд: PCB Piezotronics Страницы: 143

Бренд: JYTEK Страницы: 32

Бренд: JYTEK Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды