Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 155 / 516

background image

Procedure

Step 1

The fiber patch-panel tray requires 1 to 2 RUs of space in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm)
rack, depending on whether you are installing a standard or deep patch-panel tray. (The standard tray requires
1 RU, and the deep 32-channel, 40-channel, and mesh patch panel trays each require 2 RUs.) Locate the RMU
space specified in your site plan.

Step 2

Verify that the mounting brackets attached to the unit are correct for your rack size. Complete

the Mounting Bracket to Fit a 19-inch (482.6-mm) Rack (ANSI Only), on page 33

as required.

Step 3

Align the tray chassis with the rack mounting screw holes, then insert and tighten the four screws.

Step 4

Connect a frame ground to the ground terminal provided on either side of the chassis. Use minimum #14
AWG wire.

Step 5

Repeat Steps 2 through 4 for each patch-panel tray you want to install.

Step 6

Return to your originating procedure (NTP).

DLP-G29 Install the Fiber-Storage Tray

This task installs the fiber-storage tray. The fiber-storage tray stores slack
fiber-optic cable.

Purpose

#2 Phillips Dynamometric screwdriver

Tools/Equipment

None

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Procedure

Step 1

The fiber-storage tray requires 1 RU in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack. Locate
the RMU space specified in your site plan.

Step 2

Verify that the mounting brackets attached to the unit are correct for your rack size. Complete the

Reverse the Mounting Bracket to Fit a 19-inch (482.6-mm) Rack (ANSI Only), on page 33

as required.

Step 3

Align the chassis with the rack mounting screw holes, insert the four screws, and tighten.

Step 4

Return to your originating procedure (NTP).

Cisco ONS 15454 Hardware Installation Guide

125

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

DLP-G29 Install the Fiber-Storage Tray

«
...
153
154
155
156
157
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Megaplex II 4U Guide

Бренд: American Megatrends Страницы: 26

Бренд: 3C-Link Страницы: 6

Бренд: National Instruments Страницы: 16

Бренд: IDK Страницы: 44

Бренд: AIC Страницы: 20

Бренд: Xena Networks Страницы: 16

FortiGate FortiGate-5140

Бренд: Fortinet Страницы: 2

Бренд: Tektronix Страницы: 214

Sivoia QS roller 100

Бренд: Lutron Electronics Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды