Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 167 / 516

background image

The MS-ISC-100T is not supported in a subtended shelf.

Note

Procedure

Step 1

Open the latches/ejectors on the card.

Step 2

Use the latches/ejectors to firmly slide the card along the guide rails into the appropriate slot in the node
controller shelf until the card plugs into the receptacle at the back of the slot. The card can be installed in any
slot from Slot 1 to 6 or 12 to 17. Cisco recommends that you install the MS-ISC-100T cards in Slot 6 and Slot
12.

Step 3

Verify that the card is inserted correctly and close the latches/ejectors on the card.

It is possible to close the latches/ejectors when the card is not completely plugged into the backplane.
Ensure that you cannot insert the card any further.

Note

Step 4

Verify the LED activity:

• The red FAIL LED blinks for 35 to 45 seconds.

• The red FAIL LED turns on for 15 to 20 seconds.

• The red FAIL LED blinks for approximately 3 minutes.

• The red FAIL LED turns on for approximately 6 minutes.

• The green ACT or ACT/STBY LED turns on. The SF LED can persist until all card ports connect to

their far end counterparts and a signal is present.

If the red FAIL LED does not turn on, check the power.

Note

If you insert a card into a slot provisioned for a different card, all LEDs turn off.

Note

Step 5

Repeat all the steps for the redundant MS-ISC-100T card.

Step 6

Return to your originating procedure (NTP).

Multishelf Management

The maximum number of shelves that can be aggregated under a single IP address is 30 shelves. It is
recommended to use TCC3 card in the node controller if the number of subtended shelves exceed 12 shelves.

Multishelf LAN Topologies

The following sections describe various multishelf LAN topologies in Cisco ONS 15454 shelves.

Cisco ONS 15454 Hardware Installation Guide

137

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

Multishelf Management

«
...
165
166
167
168
169
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: Overland Storage Страницы: 4

Бренд: GearMo Страницы: 6

Бренд: REDCAT Страницы: 24

Бренд: Overland Storage Страницы: 3

Бренд: Paradyne Страницы: 11

Hotwire 8820 GranDSLAM Series

Бренд: Paradyne Страницы: 60

Бренд: 3Com Страницы: 2

Бренд: H3 Страницы: 49

Бренд: CYP Страницы: 28

Бренд: Cisco Страницы: 294

Бренд: Cisco Страницы: 289

AS5350 - Universal Access Server

Бренд: Cisco Страницы: 102

Бренд: Cisco Страницы: 42

Бренд: Cisco Страницы: 422

Бренд: Cisco Страницы: 428

Бренд: Cisco Страницы: 74

Бренд: Cisco Страницы: 284

Бренд: Cisco Страницы: 466

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды