Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 98

Страница: 98 / 370

Symptom List:

P0132-O2 SENSOR 1/1 VOLTAGE HIGH
P0138-O2 SENSOR 1/2 VOLTAGE HIGH

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0132-O2 SENSOR 1/1 VOLTAGE
HIGH.

When Monitored and Set Condition:

P0132-O2 SENSOR 1/1 VOLTAGE HIGH

When Monitored:

The engine running for 119 seconds. O2 Sensor Heater Temperature is

greater than 350°C (662°F). Battery voltage greater than 10.99 volts.

Set Condition:

The Oxygen Sensor voltage is above 3.7 volts for 60 seconds. Two trip

fault.

P0138-O2 SENSOR 1/2 VOLTAGE HIGH

When Monitored:

The engine running for 119 seconds. O2 Sensor Heater Temperature is

greater than 350°C (662°F). Battery voltage greater than 10.99 volts.

Set Condition:

The Oxygen Sensor voltage is above 3.7 volts for 60 seconds. Two trip

fault.

POSSIBLE CAUSES

O2 SENSOR VOLTAGE ABOVE 3.7 VOLTS

O2 SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE

O2 SENSOR RETURN CIRCUIT SHORTED TO VOLTAGE

O2 SENSOR

O2 SENSOR SIGNAL CIRCUIT OPEN

O2 SENSOR RETURN CIRCUIT OPEN

PCM

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Результаты поиска

Содержание Pacifica CS 2004

Отзывы:

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 98 / 370

Результаты поиска

Содержание Pacifica CS 2004

Отзывы: