manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 40 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 40

TEST

ACTION

APPLICABILITY

11

NOTE: The conditions that set this DTC are not present at this time. The
following test may help in identifying the intermittent condition.
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
Start the engine.
Gently tap on the Crank Position Sensor and wiggle the CKP Sensor.
Turn the ignition off.
Inspect the Sensor harness connector, PCM harness connector, Sensor connector, and
PCM connector for loose, bent, corroded, or pushed out pins/terminals.
Inspect the related wire harness and the splices in the (K24) CKP circuits.
Were any problems found?

All

Yes

→

Repair the wiring/connector concerns as needed or replace the
Crankshaft Position Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Test Complete.

34

DRIVEABILITY - NGC

P0016-CRANKSHAFT/CAMSHAFT TIMING MISALIGNMENT —

Continued

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов