Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 55

Symptom:

P0072-AMBIENT TEMP SENSOR LOW

When Monitored and Set Condition:

P0072-AMBIENT TEMP SENSOR LOW

When Monitored:

The ignition key on.

Set Condition:

Ambient Temperture Sensor is less than .0392 of a volt at the PCM. One

Trip Fault.

POSSIBLE CAUSES

AMBIENT AIR TEMPERATURE SENSOR VOLTAGE BELOW 0.3 VOLTS

AMBIENT AIR TEMPERATURE SENSOR INTERNAL FAILURE

(K145) AAT SIGNAL CIRCUIT SHORTED TO GROUND

(K25) AAT SIGNAL CIRCUIT SHORTED TO (K4) SENSOR GROUND CIRCUIT

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read the Ambient Air Temperature Sensor voltage.

Is the voltage below 0.3 of a volt?

All

Yes

→

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the Ambient Air Temperature Sensor harness connector.
Ignition on, engine not running.
With the DRBIII

t

, read Ambient Air Temperature Sensor voltage.

Is the voltage above 1.0 volt?

All

Yes

→

Replace the Ambient Air Temperature Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

3

Turn the ignition off.
Disconnect the Ambient Air Temperature Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (K25) AAT Signal circuit in the
Ambient Air Temperature Sensor harness connector.
Is the resistance below 100 ohms?

All

Yes

→

Repair the short to ground in the (K145) AAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

49

DRIVEABILITY - NGC

«
...
53
54
55
56
57
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов