manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 326 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 326

Symptom:

*NO CRANK CONDITION

POSSIBLE CAUSES

REPAIR MECHANICAL CONDITION

TRANSMISSION RANGE SENSOR

BATTERY CIRCUIT RESISTANCE TOO HIGH

IGNITION SWITCH OUTPUT CIRCUIT OPEN

STARTER RELAY CONTROL CIRCUIT OPEN

STARTER RELAY OUTPUT CIRCUIT OPEN

FUSED B(+) CIRCUIT OPEN

FUSED IGNITION SWITCH OUTPUT (START) CIRCUIT OPEN

STARTER

STARTER MOTOR RELAY

STARTER RELAY

TEST

ACTION

APPLICABILITY

1

NOTE: Check all PCM powers and grounds before continuing.
NOTE: Ensure that SKIS is operating properly. Check the SKIM for DTC. If
a SKIM DTC(s) is present diagnose them first before continuing.
WARNING: MAKE SURE THE BATTERY IS DISCONNECTED, THEN WAIT
TWO MINUTES BEFORE PROCEEDING.
Turn the engine over by hand to ensure the engine is not seized.
Is the engine able to turn over?

All

Yes

→

Go To

2

No

→

Repair the mechanical condition preventing the starter motor
from cranking.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

Turn the ignition off.
Disconnect the PCM harness connectors.
Move the Gear selector through all gear positions, from Park to 1st and back.
While moving the gear selector through each gear, measure the resistance between
ground and the P/N Position Switch Sense circuit.
Did the resistance change from above 10.0 ohms to below 10.0 ohms?

All

Yes

→

Go To

3

No

→

Replace the Transmission Range Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

3

Turn the ignition off.
Check the Battery Cables for high resistance using the service information proce-
dure.
Did either Battery Cable have a voltage drop greater than 0.2 volt?

All

Yes

→

Repair the Battery circuit for high resistance.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

Go To

4

320

STARTING

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов