Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 322 | Manualshive

Страница: 322 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 322

TEST

ACTION

APPLICABILITY

2

Check for any open fuses in the PDC or Fuse Block that may be related to the No
Start condition.
Are any of the fuses open?

All

Yes

→

Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors, repair as necessary. Replace the Fuse.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

3

Turn the ignition on.
With the DRBIII

t

, actuate the ASD Fuel System test.

Note: It may be necessary to use a mechanics stethoscope in the next step.
Listen for fuel pump operation at the fuel tank.
Does the Fuel Pump operate?

All

Yes

→

No

→

Caution: Stop All Actuations.

4

Turn the ignition off.
WARNING: The fuel system is under a constant pressure even with the
engine off. Before testing or servicing any fuel system hose, fitting or line,
the fuel system pressure must be released.
Install a fuel gauge.
Turn the ignition on.
With the DRBIII

t

, actuate the ASD Fuel System test and observe the fuel pressure

gauge.
NOTE: Fuel pressure specification is 400 kPa +/- 34 kPa (58 psi +/- 5 psi).
Choose a conclusion that best matches your fuel pressure reading.

All

Below Specification

Within Specification

Above Specification

Replace the fuel pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

Caution: Stop All Actuations.

316

STARTING

*ENGINE CRANKS DOES NOT START —

Continued

«
...
320
321
322
323
324
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов