manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 225 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 225

Symptom:

P0563-BATTERY VOLTAGE HIGH

When Monitored and Set Condition:

P0563-BATTERY VOLTAGE HIGH

When Monitored:

The engine running. The engine speed greater than 380 RPM.

Set Condition:

Battery voltage is 1 volt greater than desired system voltage. One Trip

Fault

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

GENERATOR OPERATION

(K20) GEN FIELD CONTROL CIRCUIT SHORTED TO BATTERY VOLTAGE

PCM

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the Battery is in good condition. Using the Midtronics
Battery Tester, test the Battery before continuing.
NOTE: Inspect the vehicle for aftermarket accessories that may exceed the
Generator System output.
Turn the ignition off.
NOTE: Ensure the generator drive belt is in good operating condition.
NOTE: Inspect the fuses in the PDC. If a fuse is found to be open use the
wiring diagram/schematic as a guide, inspect the wiring and connectors for
damage.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 3 - NGC.

2

Turn the ignition off.
Disconnect the Generator Field harness connector.
Using a 12-volt test light, jumper it across the Generator Field harness connector.
Ignition on, engine not running.
With the DRBIII

t

, actuate the Generator Field Driver circuit.

Does the test light illuminate brightly and flash on and off?

All

Yes

→

Go To

4

No

→

Go To

3

219

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов