Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 271

Страница: 271 / 370

Symptom List:

P1696-EEPROM MEMORY WRITE DENIED/INVALID
P1697-EMR (SRI) MILEAGE NOT STORED

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P1696-EEPROM MEMORY
WRITE DENIED/INVALID.

When Monitored and Set Condition:

P1696-EEPROM MEMORY WRITE DENIED/INVALID

When Monitored:

With the ignition on continuous.

Set Condition:

An attempt to program/write to the internal EEPROM failed. Also checks

at power down.

P1697-EMR (SRI) MILEAGE NOT STORED

When Monitored:

With the ignition on continuous.

Set Condition:

An attempt to program/write to the internal EEPROM failed, Also checks

at power down.

POSSIBLE CAUSES

DRB DISPLAYS WRITE FAILURE

DRB DISPLAYS WRITE REFUSED 2ND TIME

DRB DISPLAYS SRI MILEAGE INVALID

COMPARE SRI MILEAGE WITH ODOMETER

TEST

ACTION

APPLICABILITY

With the DRBIII

, perform the SRI Memory Test.

Does the DRBIII

display Write Failure?

All

Yes

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

→

Go To

With the DRBIII

, perform the SRI Memory Test.

Does the DRBIII

display Write Refused?

All

Yes

→

Go To

→

Go To

265

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Результаты поиска

Содержание Pacifica CS 2004

Отзывы:

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 271 / 370

Результаты поиска

Содержание Pacifica CS 2004

Отзывы: