manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 92 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 92

Symptom:

P0129-BAROMETRIC PRESSURE OUT-OF-RANGE LOW

When Monitored and Set Condition:

P0129-BAROMETRIC PRESSURE OUT-OF-RANGE LOW

When Monitored:

With the ignition key on. No Cam or Crank signal within 75 ms. Engine

speed at less than 250 RPM.

Set Condition:

The PCM senses the voltage from the MAP sensor to be less than 2.196

volts but above 0.0392 of a volt for 300 milliseconds.One Trip Fault.

POSSIBLE CAUSES

IAC SIGNAL CIRCUIT LOW

IAC SIGNAL CIRCUIT HIGH

INTERMITTENT CONDITION

(K6) 5 VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE

(K6) 5 VOLT SUPPLY CIRCUIT SHORTED TO GROUND

(K6) 5 VOLT SUPPLY CIRCUIT OPEN

MAP SENSOR INTERNAL FAILURE

(K1) MAP SIGNAL CIRCUIT OPEN

(K1) MAP SIGNAL CIRCUIT SHORTED TO GROUND

PCM (K6) 5 VOLT SUPPLY CIRCUIT

PCM (K1) MAP SIG CIRCUIT

TEST

ACTION

APPLICABILITY

1

NOTE: Refer to any TSBs that may apply to this DTC before proceeding.
Ignition on, engine not running.
With the DRBIII

t

, read the MAP Sensor voltage.

Is the voltage below 2.2 volts.

All

Yes

→

Go To

2

No

→

Go To

11

2

Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage of the (K6) 5 Volt Supply circuit in the MAP Sensor harness
connector.
Is the voltage between 4.5 to 5.2 volts?

All

Yes

→

Go To

3

No

→

Go To

7

86

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов