manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 165 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 165

Symptom:

P0420-CATALYTIC 1/1 EFFICIENCY

When Monitored and Set Condition:

P0420-CATALYTIC 1/1 EFFICIENCY

When Monitored:

Engine Run time greater than 90 seconds. Engine Coolant greater than

70°C (158°F) Vehicle speed greater than 20 MPH and less than 55 MPH. Engine Speed
greater than 1216 RPM and less than 1952 RPM.

Set Condition:

As catalyst efficiency deteriorates, the switch rate of the downstream O2

sensor approaches that of the upstream O2 sensor. If at any point during the test the
switch ratio reaches a predetermined value a counter is incremented by one. One Trip
Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

VISUALLY INSPECT CATALYTIC CONVERTER

EXHAUST LEAK

ENGINE MECHANICAL CONDITION

AGING O2 SENSOR

CATALYTIC CONVERTER

TEST

ACTION

APPLICABILITY

1

NOTE: A new rear O2 Sensor along with an aging front O2 Sensor may cause
the DTC to set. Review the repair history of the vehicle before continuing.
NOTE: If an O2 Sensor or Fuel System Lean DTC(s) is set along with the
Catalytic Converter Efficiency DTC, diagnose the O2 Sensor DTC(s) before
continuing.
NOTE: Check for contaminates that may have damaged the O2 Sensor and
Catalytic Converter: contaminated fuel, unapproved silicone, oil and cool-
ant, repair necessary.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

159

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов