manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 299 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 299

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Replace the Sentry Key Immobilizer Module in accordance with the Service Infor-
mation.
Turn the ignition on.
Display and erase all PCM and SKIM DTCs.
Perform 5 ignition key cycles leaving the ignition key on for 90 seconds per cycle.
With the DRB, display PCM DTCs.
Does the DRB display the same DTC?

All

Yes

→

Replace and program the PCM in accordance with the Service
Information.
Perform SKREEM VERIFICATION TEST - VER 1A.

No

→

Test Complete.

5

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running and at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wire harness. Look for parameter
values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wire harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wire harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→

Repair as necessary.
Perform SKREEM VERIFICATION TEST - VER 1A.

No

→

Test Complete.

293

DRIVEABILITY - NGC

U0168-NO SKIM BUS MESSAGES —

Continued

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов