Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 203 | Manualshive

Страница: 203 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 203

TEST

ACTION

APPLICABILITY

2

Visually and Physically inspect the PCV system.
Check for the PCV valve disconnected.
Check for an incorrect PCV valve. The PCV valve must meet OEM specifications.
Damage vacuum hose.
Were any of the above condition found?

All

Yes

→

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

3

Turn the ignition off.
Remove the IAC Motor.
Inspect the IAC Motor and passages for any obstructions or damage to motor.
Were any problems found?

All

Yes

→

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

4

Start the engine.
Inspect the vehicle for external vacuum leaks.
Inspect the engine for internal vacuum leaks.
Were any vacuum leaks found?

All

Yes

→

Repair the vacuum leak as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

5

Inspect the Air Induction System for the following problems.
Restrictions: Dirty Air Cleaner, Foreign material trapped in the air intake tube, etc.
Leaks: Air Intake tube connection, Air Cleaner housing, etc.
Were any problems found?

All

Yes

→

Repair or replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

6

Inspect the throttle body plate carbon build up or other restrictions.
Inspect the throttle linkage for binding and smooth operation.
Ensure the throttle plate is resting on the stop at idle.
Were any problems found?

All

Yes

→

Repair or replace as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Test Complete.

197

DRIVEABILITY - NGC

P0506-IDLE SPEED LOW PERFORMANCE —

Continued

«
...
201
202
203
204
205
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов