Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 32

TEST

ACTION

APPLICABILITY

5

Note: Ensure there is PCI Bus communication with other modules on the
vehicle before proceeding. If not, refer to the symptom list from the menu
and repair as necessary.
Disconnect the PCM harness connectors.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIII

t

select Pep Module Tools.

Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Press F2 again
when complete.
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the appropriate terminal of special tool #8815.
Turn the ignition on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?

All

Yes

→

No

→

Repair the PCI Bus circuit for an open.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

6

Using the schematics as a guide, inspect the wiring and connectors. Repair as
necessary. Pay particular attention to all power and ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Control Module in accor-
dance with the service information. WITH THE DRBIII

t

PER-

FORM QUICK LEARN AND REPROGRAM PINION FACTOR.
Perform 40/41TE (NGC) TRANSMISSION VERIFICATION
TEST - VER 1.

26

COMMUNICATION

*NO RESPONSE FROM TRANSMISSION CONTROL MODULE —

Continued

«
...
30
31
32
33
34
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов