manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 68 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 68

Symptom:

P0112-INTAKE AIR TEMPERATURE SENSOR LOW

When Monitored and Set Condition:

P0112-INTAKE AIR TEMPERATURE SENSOR LOW

When Monitored:

With the ignition on. Battery voltage greater than 10 volts.

Set Condition:

The Intake Air Temperature (IAT) sensor voltage is less than 0.0784 of a

volt. One trip Fault.

POSSIBLE CAUSES

IAT SENSOR VOLTAGE BELOW 1.0 VOLT

IAT SENSOR INTERNAL FAILURE

(K21) IAT SIGNAL SHORTED TO GROUND

(K21) IAT SIGNAL SHORTED TO (K4) SENSOR GROUND CIRCUIT

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, read the IAT Sensor voltage.

Is the voltage below 1.0 volt?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

2

Turn the ignition off.
Disconnect the IAT harness connector.
Ignition on, engine not running.
With the DRBIII

t

, read IAT Sensor voltage.

Is the voltage above 1.0 volt?

All

Yes

→

Replace the IAT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

3

3

Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (K21) IAT Signal circuit at the IAT
Sensor harness connector.
Is the resistance below 100 ohms?

All

Yes

→

Repair the short to ground in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

Go To

4

62

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов