Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 309

Страница: 309 / 370

Symptom List:

ROLLING CODE FAILURE
VIN MISMATCH

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be ROLLING CODE FAILURE.

When Monitored and Set Condition:

ROLLING CODE FAILURE

When Monitored:

At ignition on, after ignition on during any rolling code handshake that

occurs with the PCM due to a SKIM or PCM reset.

Set Condition:

When a PCM STATUS message with a Valid Key status is not received by

the SKIM within 3.5 seconds of transmitting the last Valid Key Code message to the PCM.

VIN MISMATCH

When Monitored:

With the ignition on.

Set Condition:

When the VIN received from the PCM does not match the VIN stored in

the SKIM’s EEPROM.

POSSIBLE CAUSES

VERIFYING PCM VIN

REPLACE SKREEM AND CHECK DTC’S

INTERMITTENT WIRING HARNESS PROBLEM

PCM

TEST

ACTION

APPLICABILITY

With the DRBIII

, erase the SKREEM DTCs.

Turn the ignition off.
Wait 10 seconds.
Turn the ignition on and wait 2 minutes.
With the DRBIII

, read the SKREEM DTCs.

Does the DRBIII

display the DTC that was previously erased?

All

Yes

→

Go To

→

Go To

303

SKREEM

Содержание Pacifica CS 2004



















































































































































































































































































































































































Результаты поиска

Содержание Pacifica CS 2004

Отзывы:

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 309 / 370

Результаты поиска

Содержание Pacifica CS 2004

Отзывы: