manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 269 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 269

Symptom:

P1602-PCM NOT PROGRAMMED

When Monitored and Set Condition:

P1602-PCM NOT PROGRAMMED

When Monitored:

Ignition on.

Set Condition:

The PCM has not been programmed.

POSSIBLE CAUSES

PCM NOT PROGRAMMED

VERIFY PCM PROGRAMMING

PCM

TEST

ACTION

APPLICABILITY

1

Ignition on, engine not running.
With the DRBIII

t

, erase DTCs.

With the DRBIII

t

program the PCM.

Start the engine.
Allow the engine to reach normal operating temperature.
With the DRBIII

t

, read DTCs.

Does the DTC reset?

All

Yes

→

Go To

2

No

→

The PCM has been successfully programmed. Test is complete.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

NOTE: The ignition switch must be left in the off position for a minimum of
10 seconds.
Cycle the ignition switch to the off position and then back to run.
Attempt to program the PCM.
Start the vehicle and allow it to reach normal operating temperatures.
With the DRBIII

t

, read DTCs.

Does the DTC reset?

All

Yes

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

The PCM has been successfully programmed into the PCM. Test
is complete.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

263

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов